Saiga Triggers and FCGs
It is important to note that Saiga rifles and shotguns have unique fire control groups (FCG) and require modification to use standard AK-pattern FCGs (basically the trigger on a Saiga is located further back in the receiver, requiring a transfer bar to connect the Saiga trigger to the rest of the FCG assembly). If you convert your Saiga to a standard AK-pattern configuration, most AK-pattern FCGs can be used, but almost all will require at least one of the below two modifications (some vendors also offer pre-modified "drop-in" FCGs specifically for use in Saigas).
note: The below considerations will ensure that an AK FCG will fit in a Saiga rifle of .223, 7.62x39mm, or 5.45 caliber. However, Saiga shotguns and Saiga rifles in .308 caliber require special trigger considerations with intricacies that our current staff cannot fully explain, thus, we will not try.
Modifications to AK-pattern FCGs for use in a Saiga
Replacing the fire control group is a critical part of the conversion process, and is one of the easiest ways to reduce your Saiga's 922r parts count. In addition to replacing three foreign parts (trigger, hammer, disconnector), a new FCG usually provides a cleaner, lighter, more pleasant trigger pull. However, it should be noted that almost all USA-made FCGs are made by casting or metal-injection-molding (MIM), so they are usually not as strong as the forged FCGs common to most overseas AKs. However, it is difficult to locate a confirmed account of a cast or MIM FCG actually failing.
note: The below considerations will ensure that an AK FCG will fit in a Saiga rifle of .223, 7.62x39mm, or 5.45 caliber. However, Saiga shotguns and Saiga rifles in .308 caliber require special trigger considerations with intricacies that our current staff cannot fully explain, thus, we will not try.
Modifications to AK-pattern FCGs for use in a Saiga
- The FCG will need to be modified with a cutting tool in order for the Saiga bolt-hold-open (BHO) device to have clearance, otherwise, the FCG will be blocked from proper cycling by the BHO. Alternatively, you can simply remove the BHO and leave the FCG unmodified, although you will obviously lose your Saiga's BHO function.
- The receiver may need to be cut for a "double hook" FCG. All Saiga receivers are cut to accept "single-hook" FCGs only, but some AK FCGs are "double-hook", which means that the top of the trigger has two hooks that engage the hammer instead of one. The double-hook FCG was the original design for the AK-47, but the FCG was later changed to a single-hook design in order to make space for a reducer (to lower the rate-of-fire). Most modern AK FCGs are single-hook and the Saiga is no exception, however, the lack of fully-automatic operation means the reducer is not necessary and the single hook design was kept out of convenience (one set of manufacturing tooling), not necessity. Double-hook FCGs can be used in a Saiga, but a slot for the second hook must be cut into the receiver, or the second hook removed from the FCG with a cutting tool. Opinions vary as to whether double-hook or single-hook FCGs are superior.
Replacing the fire control group is a critical part of the conversion process, and is one of the easiest ways to reduce your Saiga's 922r parts count. In addition to replacing three foreign parts (trigger, hammer, disconnector), a new FCG usually provides a cleaner, lighter, more pleasant trigger pull. However, it should be noted that almost all USA-made FCGs are made by casting or metal-injection-molding (MIM), so they are usually not as strong as the forged FCGs common to most overseas AKs. However, it is difficult to locate a confirmed account of a cast or MIM FCG actually failing.
Disclaimer
This website is not affiliated with, endorsed by, or generally in cahoots with any of the below manufacturers or product lines.
The below products are not claimed to be the best or worst available, they are merely listed to provide a "jumping off point" for a prospective buyer's search. Whenever possible the link will be directly to the manufacturer, but that does not always mean the product cannot be found elsewhere.
Prices are listed only to provide a general idea, not a guarantee. Prices may change over time.
This website is not affiliated with, endorsed by, or generally in cahoots with any of the below manufacturers or product lines.
The below products are not claimed to be the best or worst available, they are merely listed to provide a "jumping off point" for a prospective buyer's search. Whenever possible the link will be directly to the manufacturer, but that does not always mean the product cannot be found elsewhere.
Prices are listed only to provide a general idea, not a guarantee. Prices may change over time.
Saiga FCGs
Tapco G2 FCG - A popular USA-made FCG with a lighter pull than the original AK design, the G2 is available in single-hook or double-hook varieties.
$25 - $35
Texas AK Triggers FCG - Available only as a double-hook, this trigger claims an improved design over the original, with lighter pull and crisper feel.
$30 - $40
CSS Fire Control Group - A FCG that has been modified for drop-in fitment in all Saiga rifles and shotguns except the .410 shotgun and .308 rifle.
$40 - $50
Red Star Arms FCG - Offering highly adjustable trigger mechanics, this pricey FCG is also the only USA-made FCG that is cut from solid steel billet (not cast or MIM).
$80 - $90
Tapco G2 FCG - A popular USA-made FCG with a lighter pull than the original AK design, the G2 is available in single-hook or double-hook varieties.
$25 - $35
Texas AK Triggers FCG - Available only as a double-hook, this trigger claims an improved design over the original, with lighter pull and crisper feel.
$30 - $40
CSS Fire Control Group - A FCG that has been modified for drop-in fitment in all Saiga rifles and shotguns except the .410 shotgun and .308 rifle.
$40 - $50
Red Star Arms FCG - Offering highly adjustable trigger mechanics, this pricey FCG is also the only USA-made FCG that is cut from solid steel billet (not cast or MIM).
$80 - $90
|
|
|